DIY Valentine’s Day Jeweled Wreath with Paper Mart

This project is in collaboration with Paper Mart. I was provided supplies to create a Valentine’s Day tutorial. All opinions are my own. My full Disclosure Policy is here.

Most of the year I have a seasonal wreath hanging on my door…but realized that for Valentine’s Day I’ve never made anything appropriate for the holiday. My initial thoughts were to just do something easy peasy (and a little cheesy 😉 : gluing foam cut-out hearts to a wreath ring and call it that. Then I decided I wanted to take things up a notch and make something sparkly, chic, and not so obviously Valentine’s Day…and Paper Mart came to my rescue. (And let me preface this by saying this project is as easy as gluing stuff onto a wreath form!!) Here’s how you can make your own bejeweled beautiful sophisticated wreath – not just for Valentine’s Day but for any day of the year:

How to Make a Jeweled Valentine’s Day Wreath

You Need:

16″ wreath frame / 1+ pack of pink round acrylic jewels / 1+ pack of 20mm crystals / 1+ pack of 12mm crystals / silver wired lame ribbon / jewel placement tool (optional) / slow-drying clear glue (recommended: Dazzle Tac) / scissors / glue gun

How To:

1. Start wrapping the end of your ribbon to the top of the frame (I didn’t even need a glue gun to secure because the wire inside of the ribbon will hold it down!).

2. Wrap ribbon around the entire frame to make a gluable ribbon base, overlapping the ribbon slightly.

3. Cut the ribbon once you meet the beginning of it again, fold over the cut edge slightly, and glue down the end to cover up the other ribbon end.

4.Now make a bow for your wreath. Here’s how:

How to Make the Perfect Bow (gluing wired ribbon)

Cut 3 pieces of ribbon. For 1.5″ wide ribbons like this, the measurements I used were:

  • 3.75″
  • 18.75″
  • 26.75″

5.Take the middle length of ribbon and hot glue the ends overlapping (about 1/2″) to make a loop.

6. Press the loop down in the middle and glue the inner center of the loop at the overlapping area to the other side of the loop on the inside. This now creates 2 loops: the loops of the bow.

7. Glue the center of the longest piece to the back of the loop you created at the overlap, right sides together.

8. Place the shortest piece on top of the bundle at the center front of the two loop piece and glue down.

9. Pull the ends of the shortest ribbon piece to the back of the bundle, scrunching in at its sides, and glue at the back, the ends slightly overlapping.

10. Fluff out your ribbon by making the loops large and round, and fold the long ribbon piece down so it’s visible behind the loops. Add some waviness to the longer ribbon ends.

11. Cut the long ribbon ends at an angle.

12. Top off your wreath by hot-gluing on a bow made from the wired ribbon.

13. Now it’s time to have some fun! Spread slow-drying glue onto the back of a large gemstone, and place onto the wreath. (I know it shows E6000 glue in the photo, but I quickly found that Dazzle Tac was much better.) I chose an evenly-spaced placement.

14. Then repeat for the medium-sized jewels (these too I opted for an evenly-spaced placement around the wreath).

15. Repeat the process for the smallest rhinestones. You could use a jewel placement tool to help place gems quickly, but you can also use tweezers or even your fingers depending on how much precision you want. It’s always helpful to take a step back and assess your work. I chose to create a cluster with the smaller pink jewels near the bottom of the wreath; you can add more or less depending on what look you like.

And that’s it!

 

Allow to dry, then hang on your door – or wall – or use as a centerpiece for your delicious Valentine’s Day dinner. Sparkle – ribbon – jewels – beautiful!

Happy DIY’ing!

xo

Carly

Save

Leave Comment

Pin It on Pinterest